Configuring bootable NVIDIA RAID array for a Windows XP 32-bit/Windows XP 64-bit Edition installation

Answer ID 236
Published 03/18/2005 02:51 PM
Updated 07/20/2011 04:59 PM

Configuring bootable NVIDIA RAID array for a Windows XP/Windows XP 64-bit Edition installation

This article will explain how to configure a bootable NVIDIA RAID arrary on an nForce based motherboard which supports the NVIDIA NVRAID.  You will need a blank 1.44MB floppy disk to create an F6 install floppy with the NVIDIA RAID drivers used during the installation of Windows XP or Windows XP 64-bit Edition. 

The first step is to create an F6 install floppy disk.  Insert a blank 1.44MB floppy disk into your computer.  Next, download the appropriate nForce driver for the chipset your motherboard uses.  You may do this on any computer that has a floppy disk drive as the drivers will not be immediately installed.  The latest nForce drivers are available for download from the following URL:

NVIDIA Software Download Page


Download the driver to your PC. Once the driver has completely downloaded to your computer, run the file by double-clicking on the file.

You will first be prompted by a license areement.  Once you have read the license agreement, you may proceed to the next step if you choose so.  The Installshield will then prompt you for a location where the install files should be extracted to.  For example, if you have downloaded the nForce driver version 6.86 for Windows 2000/XP 32-bit, the window will look similar to the image below:

The default location is fine.  Pleaese remember this location as you will need to browse to this location after the next step.  Proceed by clicking on the "Next"button.  The files will be extracted to the location given.  Once the files have been extracted, cancel the rest of the Installshield installation process as you do not want to install the nForce drivers.

Next, go to the directory where the files were extracted to.  You will find several files and folders in this directory.  The Windows F6 floppy installation drivers will be located in the directory


Copy these files to your floppy disk.  Your floppy disk now has the necessary files needed to begin the Microsoft Windows installation on your nForce system. 

Once you have downloaded the drivers, unzip the file. Copy the extracted driver files to your floppy disk.  This will be used later during the installation of Windows.  Please proceed now to your nForce based computer to configure the RAID array.  The next steps will guide you with setting up a RAID array through the motherboard's BIOS and NVRAID BIOS.

Setting Up the BIOS 

1. Start your computer and enter the motherboard BIOS.  Most motherboards require you to press the "Delete" key on your keyboard in order to enter the BIOS.  If your motherboard is different, then you will need to consult with your motherboard manufacturer for instructions on how to enter the BIOS.


2. Use the arrow keys to select Integrated Peripherals and then press the Enter key on your keyboard.

The Integrated Peripherals screen should appear similar to the screenshot below.


3. Use the arrow keys to select RAID Config 

4. Press Enter 

The RAID Config screen should look similar to the screenshot below


5. From the RAID Config window, globally enable RAID, then enable the SATA ports with the disks that you want to use for RAID.

If RAID is enabled globally but not enabled on the individual SATA port, disks on that
port can only be used for non-RAID applications.

6. Press F10 to save the configuration and exit (your motherboard may have different instructions for saving and exiting the BIOS).  Your PC should reboot.

7. Enter the RAID BIOS Setup by pressing F10 when prompted, and proceed to set up the
NVIDIA RAID BIOS as described in the next section.

Configuring the NVIDIA RAID BIOS 

The NVIDIA RAID BIOS set up lets you choose the RAID type and which hard drives you want to make part of the array.

Entering the RAID BIOS Setup:

1 Wait until you see the RAID software prompting you to press F10.

The RAID prompt appears as part of the system POST and boot process prior to loading of the OS. You have a few seconds to press F10 before the screen disappears.

2 Press F10.

The NVIDIA RAID Utility—Define a New Array screen appears 


Assigning the Disks 

The disks that you enabled from the RAID Config BIOS setup page appear in the Free Disks block. These are the drives that are available for use as RAID array disks.

To designate a free disk to be used as a RAID array disk,
1. Tab to the Free Disks section.

The first disk in the list is selected

2. Move it from the Free Disks block to the Array Disks block by pressing the rightarrow key.

The first disk in the list is moved, and the next disk in the list is selected and ready to be moved.

3. Continue pressing the right-arrow key until all the disks that you want to use as RAID array disks appear in the Array Disks block.


Completing the RAID BIOS Setup

1. After assigning your RAID array disks, press F7.


2. Press Y to clear the disk data.

The Array List screen appears, where you can review the RAID arrays that you have set up.


3. Use the arrow keys to select the array that you want to set up, then press B to specify the array as bootable.

4. Press Enter to view and verify details.


The Array Detail screen shows various information about the array that you selected, such as Striping Block used, RAID Mode, Striping Width, Disk Model Name and disk capacity.

5. If you want to mark this disk as empty and wipe out all its contents, press C.

6. At the prompt, press Y to wipe out all the data, otherwise press N.

7. Press Enter again to go back to the previous screen and then press F10 to exit the RAID setup.  Your PC should restart.

Installing the RAID Drivers

1. Insert your Windows XP or Windows XP 64-bit Edition installation CD to proceed with the installation of your operating system.  Make sure your CD ROM/DVD ROM is bootable from your motherboards BIOS to boot off of the Windows installation CD. 

The Windows Setup program starts. 

2. When prompted by Windows, press F6 and wait a few moments for the Windows Setup screen to appear. 


3. Windows does not include NVRAID drivers for your RAID controller on the Windows installation CD.  From the Windows Setup screen, insert the  F6 install floppy disk with the NVIDIA RAID drivers which you created earlier.  To specify the NVIDIA drivers, press S and then press Enter.

The following Windows Setup screen appears:


4. Select "NVIDIA RAID CLASS DRIVER (required)" and then press Enter

5. Press S again at the Specify Devices screen, then press Enter.

6. Select "NVIDIA NForce Storage Controller (required)" and then press Enter.

The following Windows Setup screen appears listing both drivers:


7. Press Enter to continue with Windows XP or Windows XP 64-bit Edition installation.

Be sure to leave the floppy disk inserted in the floppy drive until the blue screen portion of Windows installation is completed.  When Windows prompts you to remove all disks, you may then take out the floppy disk.

8. Follow the instructions on how to install Windows XP.

After Windows XP is completely installed, proceed to install the nForce driver package which you previously downloaded from  This will not only add drivers for your other nForce components but also the MediaShield application to allow you to access and troubleshoot your RAID array from wthin Microsoft Windows.

Was this answer helpful?
Your rating has been submitted, please tell us how we can make this answer more useful.


Chat online with one of our support agents



Contact Support for assistance